CHENFENGIntelligent Control

Selection & comparison 2026-11-05 6 min read

ACS580 or ACS880: overload, encoder and DC bus decide it

Same panel, same tool, same parameter logic. The three questions that separate the ranges are duty class, feedback and where the braking energy goes.

Definition

The ACS580 is ABB's general-purpose drive for pumps, fans and conveyors up to 500 kW; the ACS880 is the industrial range, up to 5.6 MW, with encoder feedback, a common DC bus and expandable safety functions.

The short answer

Buy the ACS580 for one motor on a normal-duty load in a 400 V panel. Buy the ACS880 when the load needs encoder feedback, regenerative braking, a shared DC bus, more than one option slot, or a frame above 500 kW.

  • 150%overload for 60 s on a 580
  • 690 Vtop voltage, ACS880 only
  • 1option slot on a 580
01

When it fits, and when it does not

The two ranges share a control panel, a parameter structure and the Drive Composer tool, so a maintenance team that can commission one can commission the other. That is deliberate, and it is why the choice is often made on price alone, which is the wrong axis.

Three questions separate them in practice: how hard is the load pushed, does the motor need feedback, and does the braking energy have to go somewhere other than a resistor. Answer those and the model number follows.

Match the drive to the load, not to the motor nameplate
If the load looks like thisSpecifyBecause
Centrifugal pump or fan, 110% overload, 400 V supplyACS580Normal-duty sizing plus built-in pump macros gets it running in an afternoon
Conveyor or mixer pulling 150% for a minute every cycleACS880, or a 580 sized on heavy-duty currentThe 580 does it only when sized from the heavy-duty column, which erases most of the price gap
Winder, unwinder, crane or hoistACS880Torque at zero speed, brake control and encoder feedback are part of the platform
Machine where braking energy should feed another axisACS880 multidriveOnly the 880 has a common DC bus; the 580 is standalone with its own rectifier
Load above 500 kW, or a 690 V supplyACS880Both limits sit outside the 580 range
Long motor cables, high switching frequency, hot cabinetACS880 with du/dt and common-mode filteringAn industrial-drive configuration, not a general-purpose one

If two rows point at the ACS880, stop looking at the 580. If none do, the 580 is cheaper and the difference is real money.

02

Key differences

Read the overload, encoder and DC bus rows first. The rest are consequences: slot count, frame construction, enclosure and price all follow from those three.

ACS580 and ACS880 on the points that change the order
ItemACS580ACS880Why it decides the order
Power range0.75 to 500 kW0.55 to 5600 kWAbove 500 kW there is no choice
Voltage200 to 240 V, 380 to 480 V200 to 240 V, 380 to 500 V, 525 to 690 VA 690 V plant is ACS880 only
Overload150% for 60 s on heavy duty150% as standard, up to 200% peakA 580 on a 150% duty must be sized from the heavy-duty column
Encoder feedbackNone, and no interface optionTTL, HTL, resolver, EnDat, SSI through FEN modulesClosed-loop positioning rules the 580 out
Common DC busNoYes, multidrive with shared DC busOne axis absorbs the braking energy of another
Regenerative supplyNoYes, with an active supply moduleCranes, test benches, downhill conveyors, unwinders
SafetySTO as standard (SIL 3, PL e)STO plus FSO-12 and FSO-21 optionsSS1, SLS and SBC inside the drive instead of relays
Option slotsOneSeveral: FIO, FEN, FPNO, FSOOn a 580 it is fieldbus or extra I/O, never both
ProgrammingAdaptive programming, 30 blocksIEC 61131-3 with Drive Application BuilderMachine logic inside the drive needs the 880
EnclosureIP21 and IP55IP21, IP22, IP54, IP55, C5 coatingWash-down and corrosive sites

Deliberately absent: motor control quality. Both ranges come from ABB's common drive architecture and both hold torque at low speed on a standard induction motor.

03

What to specify, in order

Size on current and duty, never on kW

A 22 kW motor at 400 V draws roughly 42 A, but frames differ in what they deliver at 150% for 60 seconds. Take the nameplate current, multiply by the overload the process needs, then pick the frame from the matching column. A 580 sized on normal duty trips on a load its heavy-duty twin carries without complaint.

Decide whether the motor needs feedback

If the machine positions, synchronises two shafts or must hold torque at zero speed, the drive needs an encoder interface. The ACS580 has none and cannot be given one. That single question ends the discussion more often than price does.

Follow the braking energy

A hoist, a winder or a downhill conveyor regenerates. There are three destinations: a resistor as heat, a regenerative supply back to the network, or another axis on a common DC bus. The 580 offers the first only, so a project wanting the second or third is an 880 project.

Count the option slots before you commit

A 580 with PROFINET has already used its single slot. If the same drive also needs an extra analog input or a relay board, the slot count moves you to the 880. Check the option list at quote stage, not at commissioning.

Price the installed drive, not the drive

Filter, choke, brake chopper, resistor, encoder module, cabinet depth and cooling all sit around the unit. On a 250 kW pump those accessories can cost more than the difference between the ranges.

04

Common pitfalls

  • Sizing by kW on a 150% load

    The most common re-order in this family. The kW on the nameplate describes normal duty; the frame you need is set by heavy-duty current. Send the motor current in the request, not only the power.

  • Expecting a brake chopper inside

    On larger frames it is not, and the resistor is sized to the inertia and the deceleration time, not to the drive rating. A resistor picked by kW overheats on the first fast stop.

  • Treating IP55 as a trim option

    The IP55 variant is a different frame with different depth and cable entry. An IP21 unit ordered into a wash-down area fails at the first hose-down, and water ingress is excluded from the warranty.

  • Copying a parameter file between ranges

    Both use Drive Composer, so the backup looks portable. It is not: parameter groups and default macros differ, and a 580 backup restored into an 880 leaves part of the configuration at factory values.

05

Questions we get on the quote desk

Can an ACS580 replace an ACS880 if the kW matches?
Only if the application has no encoder, no shared DC bus, no regenerative requirement and fits 150% for 60 seconds. If any of those applies, the replacement is another ACS880, and the kW figure alone will not tell you that.
Which drive for a pump station with three pumps?
Three standalone ACS580 units if each pump has its own starter and you only need speed control. An ACS880 multidrive if the pumps share a DC bus and one should absorb the braking energy of another.
Is a soft starter enough instead of a drive?
If the pump or fan only needs a controlled start and stop, a soft starter such as the PSTX is smaller and cheaper and removes the harmonic question. A drive earns its price when the process needs variable speed, pressure control or part-load energy saving.
Can either range run on 690 V?
Only the ACS880. The ACS580 stops at 480 V, which is why mining and marine projects rarely see it.
06

The models this guide names

Still deciding

Send the model number. We answer with a price, a condition and a date.

One line per part is enough. Quote back within 4 working hours, Monday to Friday 09:00–18:00 CST. No account, no minimum quantity, no obligation.

WhatsApp Request a Quote
WhatsApp